Termékek kávézó berendezési elemek (284)

Product Features: • Designed for push-pull tube output circuits. • Enclosed (shielded), 4 slot, above chassis Type "X" mounting. • Frequency response 30 Hz. to 30 Khz. at full rated power (+/- 1 db max. - ref. 1 Khz.) minimum. • Insulated flexible leads 8" min. • Manufactured with plastic coil forms for coil support and insulation. • Typical applications - Push-Pull: triode, Ultra-Linear pentode, pentode and tetrode connected audio output. • Due to the unique interleaving of the windings BOTH secondary windings must be engaged to meet specifications.

Product Features: • Couple 3.2, 8 or 16 Ohm speakers to 25 or 70 volt line outputs of amplifiers. • Up to 5 power tap levels available (except 117F2 which has 4). • Primary taps marked in watt (no calculation necessary), to match speaker power. • Frequency response 100 Hz. to 9 Khz. (1 db. reference @ 1 Khz.). • Insertion loss less than 2 db. • Distortion is less than 1.25" @ 100 Hz. at maximum power. • Horizontal, channel bracket, 2-hole (.187" dia.) mounting. • All models have solder lugs, also suitable for slip on jumper connections. • Total power requirements of speakers should not exceed the rated power of each transformer or rated power of the amplifier.

Product Features: • "Over designed" for high fidelity, single ended, Class-A, tube output circuits (triode, tetrode or pentode tubes). • Enclosed (shielded), four slot, chassis Type "X" mounting. • Frequency response at least 20 Hz. to 20 Khz. at full rated power (+/- 1 db max., ref. 1 Khz). • Insulated flexible leads 8" min. • For maximum versatility, all units (except the 1642SE and 1638SEA do NOT include this screen tap as they were designed principally for high impedance triode tubes. • High quality laminations, (M6) grain oriented silicon steel. • Core is gapped to reduce core saturation in Class-A tube amplifier circuits.

Product Features: • Designed for general purpose or replacement use in push-pull tube output circuits. • Frequency response: 150 Hz. - 15 Khz. (+/- 1db max. ref. 1 Khz.). • Open style with minimum 5" long primary leads, secondary solder lugs for convenient secondary connections.

Product Features: • Applications: Driver, Input, Interstage, Isolation. • 100mW power level at 200Hz. - 15kHz. • Pin type (0.0375" x .02"), P.C. board mount. • Economical, open type construction. • Frequency response 200 Hz. - 15 Khz. (+/- 1 db, ref. @ 1 Khz.). • Total distortion less than 0.5% for outputs at 200 Hz., decreasing at higher frequencies. • Insertion loss less than 1/2 db. • Bifilar wound for balanced capacitive and resistance characteristics, on pin bobbins for standard 0.187" grid pin spacing. • Insulation test 1500V rms, • Net weight: 0.5 oz.

Dalroad supply a wide range of DEUTSCH Connectors for industrial commercial vehicle applications including AEC, DRB, DRC, DT (DT Detector), DTHD, DTM, DTP, DTV, HD10, HD30, HDP20, HDSCS, IMC and STRIKE connectors, contacts, tools, and accessories. Order DEUTSCH connectors online today on our new website: shop.dalroad.com Request the DEUTSCH catalogue from Dalroad today at http://www.dalroad.com/new-deutsch-connector-catalogue/

Product Features: • Primary 115VAC, 60 Hz. • Secondary taps @ 90, 100, 110, 115, 120 and 130 VAC. • Electrostatic shield between primary and secondary. • Connection by flexible leads, 8" minimum length. • Perfect for critical line voltage needs (examples: Older "Classic" tube equipment or Japanese 100V equipment). • CSA certified (#LR3902) - except 169J. • Remember - These units do NOT convert line frequency.

Product Features: • Designed with nickel alloy cores for high performance and Wide Bandwidth. • Frequency Response: 20 Hz - 20 kHz ±0.35 dB, (ref. @ 1 kHz). • Low distortion at levels up to +27 dBu @ 20 Hz. • Excellent Shielding - Mu Metal Enclosures. • Line Output Transformers are open style (not Mu Metal).

Product Features: • Low profile mounting, dual - split bobbin design. • Low primary to secondary coupling, balanced windings, no electrostatic shield required and low EMD radiation due to semi-toroidal design. • Universal dual primary 115/230V - 50/60 Hz. • High insulation - Hipot of 1,750V RMS. • Class B insulation - 130°C. • C UL US recognized. UL file #E270860.

Product Features: • Designed for push-pull tube output circuits. • Enclosed (shielded), 4 slot, above chassis Type "X" mounting. • Frequency response 30 Hz. to 30 Khz. at full rated power (+/- 1 db max. - ref. 1 Khz.) minimum. • Insulated flexible leads 8" min. • Manufactured with plastic coil forms for coil support and insulation. • Typical applications - Push-Pull: triode, Ultra-Linear pentode, pentode and tetrode connected audio output. • Due to the unique interleaving of the windings BOTH secondary windings must be engaged to meet specifications.

Product Features: • Used to measure the voltage of 120 VAC systems with 5 Volt full scale A.C. voltmeters. • 50/60 Hz. operation. • Choice of chassis mount or P.C. board pin mount. • High accuracy windings (1%). • VA rated for 0.020 VA.

Product Features: • Pin type (0.25" length and 0.025" square), P.C. board mount. • Economical, open type, horizontal bracket construction. 149 Series includes clinching lugs for extra mounting strength. • Frequency response 200 Hz. - 15 Khz. (+/- 1 db, ref. @ 1 Khz.). • Total distortion approximately 2% for drivers and 1% for outputs at 200 Hz., decreasing at higher frequencies. • Insertion loss less than 1/2 db. • Bifilar wound for balanced capacitive and resistance characteristics, on pin bobbins for standard 0.2" grid pin spacing. • Insulation test 250V rms. • Net weight: 0.6 oz. (148 Series) and 1.0 oz. (149 Series).

Product Features: • Designed with nickel alloy cores for high performance and Wide Bandwidth. • Frequency Response: 20 Hz - 20 kHz ±0.35 dB, (ref. @ 1 kHz). • Low distortion at levels up to +27 dBu @ 20 Hz. • Excellent Shielding - Mu Metal Enclosures. • Line Output Transformers are open style (not Mu Metal).

Product Features: • 20 Output voltages to choose from (5 - 120VAC R.M.S.). • Six VA size models available from - .5 to 24 VA. • Vertical mount, split bobbin design. • 1.2, 4.4, 10, 24 VA models are non-concentric wound. • 0.5 and 1 VA are both concentric wound. • Low primary to secondary coupling - no electrostatic shield required. • Choice of economical single primary 115V - 60 Hz. only (161 Series) or the universal dual primary 115/230V - 50/60 Hz. (160 Series). • High insulation - Hipot fo 2,000V RMS. • Class B insulation - 130°C. • CSA certified (File #LF3902) and UL recognized (File #E207860).

Product Features: • Output power models from 5 to 1,500 milliwatt level available. • P.C. board mount - square pin type (0.025" square typical). • Bifilar winding technique used on center tapped units for balanced resistive and capacitive characteristics. • Rugged black epoxy potted construction produces a completely sealed unit withstanding severe environmental conditions including those of MIL-T-27 (Grade 5, Class S). • Peak working voltage rating of: 200V. • Referring to figures 1-9, if connection is not used - no pin will exist.

Product Features: • Suitable for driving from solid state amplifiers where isolated windings are not required or can be used with the "Classic" 1600 tube output transformers to provide a 25V or 70V line output. • 8 or 16 Ohm input, 25V or 70V line output. • Frequency response 50 Hz. to 10 Khz. at full ratings. • Leads 6" long minimum. • Can be reversed for operation at high power speaker locations.

Product Features: • Designed for drop is replacement of original units. • Physically, parts were designed to look similar to original factory units (where possible). • Inductance measured at rated D.C. current. • Material used and design specs. were kept at close as possible to the original part to preserve the stock "tone". • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.

Product Features: • Designed for general purpose or replacement use (not Hi-Fi), in single ended, tube output circuits. • Frequency response: 100 Hz. - 15 Khz at full rated power (+/- 1 db max. - ref. 1 Khz). • Open style with minimum 12" long primary and secondary leads. • All sizes use butt stacked cores (using 29M6 steel) with an air gap, reduce • D.C. core saturation. • Primary impedance range from 2,500 to 10,000 Ohms. • Secondary impedance range from 4 to 32 Ohms.

Product Features: • Perfect for audio input, line matching, isolation or output transformer applications. • 500 milliwatt (+/- 1.5 db, 300 Hz. - 50 kHz.). • Epoxy potted in an attractive black moulded case, Pin type P.C. board mount (min. 0.187" length). • In some models where no center tap is required (on secondary), pin No. 5 is omitted. • Power level ratings are maximum at lowest frequency ratings. • Power can be increased slightly at higher frequencies. • Will withstand soldering for 10 sec. @ 260°C, ambient temp. 85°C max.

Product Features: • Economical single primary 115 VAC, 60 Hz. (or 117 50/60 Hz.). • Most secondaries are center tapped (C.T.) VAC (RMS). • Open style, channel bracket, two hole chassis mount. • Minimum 6" long leads. • Dual bobbin design - no electrostatic shield required. • We use Class B insulation (130°C) for extra protection - UL listed as a Class A (105°C) design. • Hi-Pot test of 2,000V RMS. • UL listed. • CSA certified.

Product Features: • Designed with nickel alloy cores for high performance and Wide Bandwidth. • Frequency Response: 20 Hz - 20 kHz ±0.35 dB, (ref. @ 1 kHz). • Low distortion at levels up to +27 dBu @ 20 Hz. • Excellent Shielding - Mu Metal Enclosures. • Line Output Transformers are open style (not Mu Metal).

Product Features: • Designed for general purpose or replacement use in push-pull tube output circuits. • Frequency response: 150 Hz. - 15 Khz. (+/- 1 db max. ref. 1 Khz.). • Open style with minimum 10" long primary and secondary leads.

Repairing your PLC, HMI, CNC, PCB, Servo Motor, Inverter, Drive, Robot or other parts with Radwell can save up to 60% against buying new. With FREE Repair Collection, a 2 Year Warranty on the entire unit and our Price Promise we won't be beaten on price. Radwell's power to repair is second to none! Call 01782 576800 for a Quote.

Product Features: • Output power models from 5 to 1,500 milliwatt level available. • P.C. board mount - square pin type (0.025" square typical). • Bifilar winding technique used on center tapped units for balanced resistive and capacitive characteristics. • Rugged black epoxy potted construction produces a completely sealed unit withstanding severe environmental conditions including those of MIL-T-27 (Grade, 5 Class S). • Peak working voltage rating of: 200V. • Referring to figures 1-9, if connection is not used - no pin will exist.

Product Features: • Designed for drop is replacement of original units. • Physically, parts were designed to look similar to original factory units (where possible). • Inductance measured at rated D.C. current. • Material used and design specs. were kept at close as possible to the original part to preserve the stock "tone". • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.

Product Features: • Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with mounting hardware. • Sealed case and wax potted core internally for stable characteristics and long life. • Wide frequency response +/- 0.5 db max. from 20 Hz. to 20 Khz. (except units over 5K ohms impedance, amy be down 1 db @ 20 Khz.). • Insertion loss of apx. 1 db. • Maximum power level +15 dbm. with specified characteristics, or higher levels with reduced low frequency performance. • Distortion is apx. 1.5% @ 20 Hz. under full power. • Electrostatic shield between pri. and sec. connected to the green lead. • Humbucking construction. • Balanced split windings on pri. and sec. for circuit versatility. Primary may be used as a secondary and vice vera for impedance matching. • Includes mounting hardware. • Lead length: Min. 4". • Shipping weight 0.4 lb. (0.18 kg).

Radwell provides on-site PLC programming, machine repairs, equipment installations and more. Our highly skilled technicians will get you up and running in no time.

Reduce warehousing costs, reduce ageing inventory and optimise warehouse space by selling your unwanted automation equipment to Radwell.

Product Features: • Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with mounting hardware. • Sealed case and wax potted core internally for stable characteristics and long life. • Wide frequency response +/- 0.5 db max. from 20 Hz. to 20 Khz. (except units over 5K ohms impedance, amy be down 1 db @ 20 Khz.). • Insertion loss of apx. 1 db. • Maximum power level +15 dbm. with specified characteristics, or higher levels with reduced low frequency performance. • Distortion is apx. 1.5% @ 20 Hz. under full power. • Electrostatic shield between pri. and sec. connected to the green lead. • Humbucking construction. • Balanced split windings on pri. and sec. for circuit versatility. Primary may be used as a secondary and vice vera for impedance matching. • Includes mounting hardware. • Lead length: Min. 4". • Shipping weight 0.4 lb. (0.18 kg).

Product Features: • Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with mounting hardware. • Sealed case and wax potted core internally for stable characteristics and long life. • Wide frequency response +/- 0.5 db max. from 20 Hz. to 20 Khz. (except units over 5K ohms impedance, amy be down 1 db @ 20 Khz.). • Insertion loss of apx. 1 db. • Maximum power level +15 dbm. with specified characteristics, or higher levels with reduced low frequency performance. • Distortion is apx. 1.5% @ 20 Hz. under full power. • Electrostatic shield between pri. and sec. connected to the green lead. • Humbucking construction. • Balanced split windings on pri. and sec. for circuit versatility. Primary may be used as a secondary and vice vera for impedance matching. • Includes mounting hardware. • Lead length: Min. 4". • Shipping weight 0.4 lb. (0.18 kg).